XBEE S2C MODULE

Availability:

Out of stock


915 Inc GST

Out of stock

This XBee S2C is an RF module designed for wireless communication or data exchange and it works on ZigBee mesh communication protocols that sit on top of IEEE 802.15.4 PHY. The module provides wireless connectivity to end-point devices in any ZigBee mesh networks including devices from other vendors. Please note that XBee is a module designed by ‘DiGi’ and ZigBee is the name of the protocol followed by XBee modules for establishing wireless communication. With a few of these modules, the user can set up their own ZigBee network up-and-running in a matter of minutes. The XBee RF Module is compatible with other units that use ZigBee technology. These include other XBee modules, ConnectPortS gateways, XBee and XBee-PRO Adapters, XBee Sensors and other products that are designated with “ZB” product name.

 

XBee S2C Pinout

XBee S2C is a 20 pin module as given in the XBee S2C pinout diagram and the description for each pin is given below.

Pin Name Description
1 VCC Power supply
2 DOUT/DIO13 UART data out pin (TXD)/GPIO
3 DIN/CONFIG / DIO14 UART data in pin (RXD)/ GPIO
4 DIO12/SPI_MISO GPIO/ Master Input-Slave Output pin of SPI interface
5 RESET Module Reset pin
6 RSS PWM /DIO10 RX Signal Strength Indicator pin / GPIO
7 PWM1/DIO11 Pulse Width Modulator/GPIO
8 RESERVED Do not connect
9 DTR/SLEEP_RQ/ DIO8 Pin Sleep Control line /GPIO
10 GND Ground
11 DIO4/ SPI_MOSI GPIO/Master Output-Slave Input pin of SPI interface
12 CTS/DIO7 Clear-to-send flow control/GPIO
13 ON_SLEEP/DIO9 Device status indicator/GPIO
14 VREF Voltage Reference for ADC
15 ASC/DIO5 Associate Indicator/GPIO
16 RTS/DIO6 Request to send flow control/ GPIO
17 AD3/DIO3/SPI_SSEL Analog input/GPIO/SPI slave select
18 AD2 /DIO2/SPI_CLK Analog input/GPIO/SPI clock
19 AD1/DIO1/SPI_ATTN Analog input/GPIO/SPI attention
20 AD0/DIO0/C Analog input/GPIO/ Commissioning

button

 

Specification:

  • Transmission Frequency: 2.4GHz to 2.5GHz
  • Number of Channels: 16 Direct Sequence Channels
  • Featured with UART (250 Kb/s maximum) and SPI (5 Mb/s maximum) interface
  • Featured with software adjustable transmitting power
  • Indoor/Urban Range: 200ft
  • Outdoor RF line-of-sight Range: up to 4000ft
  • Transmit Power Output: 6.3mW (8dBm) in Boost mode,2mW (3dBm) in Normal mode
  • RF Data Rate: 250,000 bps
  • Receiver Sensitivity: -102dBm in Boost mode, -100dBm in Normal mode
  • Supply Voltage Range: +2.1V to +3.6V
  • Operating Current: 33mA (at3.3V, for Normal mode) , 45mA (at 3.3V,for Boost mode)
  • Idle Current: 9mA
  • Maximum output current on all pins together: 40mA
  • Power-down Current: <1uA @25C
  • ESD protection: 3000V
  • Operating Temperature: -40ºC to 85° C

 

SKU: PRA-RC-0002 Category:

SHOPPING CART

close
Select an available coupon below
× How can I help you?